|
Who's Online
There currently are 5462 guests and 2 members online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
Very clear copy. No pages missing. Big bonus is that it includes supplement. Price is affordable compared to what others ask for.
;
Found the quality of the copy excellent and a very quick service. I would certainly recommend the service.
;
Good quality, clear diagrams. Exactly what I needed.
;
Good product. All the information is invcluded, but due to the complexity of the amplifier, it still is difficult to get it to operation again.
;
Very professional seller; very fast, accurate and rielable service.
TK-3118
ADJUSTMENT / ��
Replacing Q22 (FET TX final)
1. Place Q22 in its location, upside down as shown in figure 1. Make sure the location of each pin is correct. The bevelled edge is located between pin 1 and 2. (See the figure below) Replace the heat conductor sheet (G11-2664-x4) when replacing Q22.
�置Q22 (FET ���端)
1. å¦�å�¾1æ��示ï¼�å°�Q22ä¸�ä¸�é¢ å��æ�¾å�¨å®�ç��对åº�ä½�ç½®ã�� æ¯�个管è��ç��ä½�ç½®ä¸�å®�è¦�æ£ç¡®ã��æ��è§�ä½�äº�管è��1ä¸�管è��2ä¹�é�´ã�� ï¼�å¦�ä¸�å�¾æ��示ï¼� å½�ç½®æ�¢Q22æ�¶ï¼�é��ç½®ç�导è��ï¼�G11-2664-x4ï¼�ã��
TX-RX UNIT A/3 Foil side
TC2 TC1 1st IF
Bevelled edge / ��
1 2
LV
Q22 D S G
Metal post ���
4 3
Fig. 1 / �1
2. The bottom surface of Q22 must be firmly contacted to the TX-RX PCB. Solder each pin onto the top of the metal posts. Make sure the solder is between the pin and the metal post (Refer to figure 2). 2. Q22���表��须���-��PCB紧���� ��个管������顶端��起�����须��管�� ����������2�
Note:
� Make sure you are properly grounded while soldering the Q22. � Avoid adding excess solder to the metal post. � Make sure the bottom surface of Q22 is firmly contacted to the TX-RX PCB. � The metal posts for the pins are also soldered to the PCB. So, when you solder the Q22 pins to the metal posts, keep the soldering time as short as possible so that the posts are not moved.
Excessive soldering / �度��
注��
â�¢ â�¢ â�¢ â�¢ å½�ç��æ�¥Q22æ�¶ä¸�å®�è¦�å°�ç��å��碾磨æ�°å½�ã�� é�¿å��å��é��å±�æ��æ·»å� è¿�å¤�ç��å��ã�� Q22ç��åº�é�¨è¡¨é�¢ä¸�å®�è¦�ä¸�å��å°�-æ�¥æ�¶PCBç´§å¯�ç»�å��ã�� 管è��æ��对åº�ç��é��å±�æ��ä¹�è¦�ä¸�PCBç��æ�¥å�¨ä¸�èµ·ã�� æ��以ï¼�å°�Q 2 2 管è��ä¸�é��å±�æ��ç��æ�¥èµ·æ�¥æ�¶ï¼�å°½å�¯è�½ä½¿ç��æ�¥æ�¶é�´ è¶�ç�è¶�好ï¼�è¿�æ ·é��å±�æ��ä¸�æ��被移å�¨ã��
Good soldering / ���好 Metal post / ��� PCB
Q22
Q22
Wrong! The bottom surface must be firmly contacted to the PCB. �误���表��须�PCB紧����
Fig. 2 / �2
TK-260 :K, K2
33
|
|
|
> |
|