|
Who's Online
There currently are 5959 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
This manual is complete and of high quality. I am very pleased with the purchase.
;
Another excellent buy! A fully readable PDF archive. Good prints!!
;
It is wonderful done!!! a great job in scanning the manual. Superior quality in all the electric scheme. Very understandable and net!!! Thank you!
;
muy buen manual por lo completo de este algunos esquemas estan muy divididos lo que hace algo dificil el seguimiento.
;
very good manual, with detail and clarity in esquematic diagrams and waveforms .
TK-2118
ADJUSTMENT / ��
Replacing Q22 (FET TX final)
1. Place Q22 in its location, upside down as shown in figure 1. Make sure the location of each pin is correct. The bevelled edge is located between pin 1 and 2. (See the figure below) Replace the heat conductor sheet (G11-2664-x4) when replacing Q22. TX-RX UNIT A/3 Foil side
TC2 TC1 1st IF
�置Q22 (FET ���端)
1. å¦�å�¾1æ��示ï¼�å°�Q22ä¸�ä¸�é¢ å��æ�¾å�¨å®�ç��对åº�ä½�ç½®ã�� æ¯�个管è��ç��ä½�ç½®ä¸�å®�è¦�æ£ç¡®ã��æ��è§�ä½�äº�管è��1ä¸�管è��2ä¹�é�´ã�� ï¼�å¦�ä¸�å�¾æ��示ï¼� å½�ç½®æ�¢Q22æ�¶ï¼�é��ç½®ç�导è��ï¼�G11-2664-x4ï¼�ã��
Bevelled edge / ��
1 2
LV
Q22 D S G
Metal post ���
4 3
Fig. 1 / �1
2. The bottom surface of Q22 must be firmly contacted to the TX-RX PCB. Solder each pin onto the top of the metal posts. Make sure the solder is between the pin and the metal post (Refer to figure 2). 2. Q22���表��须���-��PCB紧���� ��个管������顶端��起�����须��管�� ����������2�
Note:
� Make sure you are properly grounded while soldering the Q22. � Avoid adding excess solder to the metal post. � Make sure the bottom surface of Q22 is firmly contacted to the TX-RX PCB. � The metal posts for the pins are also soldered to the PCB. So, when you solder the Q22 pins to the metal posts, keep the soldering time as short as possible so that the posts are not moved.
Excessive soldering / �度��
注��
â�¢ â�¢ â�¢ â�¢ å½�ç��æ�¥Q22æ�¶ä¸�å®�è¦�å°�ç��å��碾磨æ�°å½�ã�� é�¿å��å��é��å±�æ��æ·»å� è¿�å¤�ç��å��ã�� Q22ç��åº�é�¨è¡¨é�¢ä¸�å®�è¦�ä¸�å��å°�-æ�¥æ�¶PCBç´§å¯�ç»�å��ã�� 管è��æ��对åº�ç��é��å±�æ��ä¹�è¦�ä¸�PCBç��æ�¥å�¨ä¸�èµ·ã�� æ��以ï¼�å°�Q 2 2 管è��ä¸�é��å±�æ��ç��æ�¥èµ·æ�¥æ�¶ï¼�å°½å�¯è�½ä½¿ç��æ�¥æ�¶é�´ è¶�ç�è¶�好ï¼�è¿�æ ·é��å±�æ��ä¸�æ��被移å�¨ã��
Good soldering / ���好 Metal post / ��� PCB
Q22
Q22
Wrong! The bottom surface must be firmly contacted to the PCB. �误���表��须�PCB紧����
Fig. 2 / �2
TK-260
:K, K2
33
|
|
|
> |
|