|
Who's Online
There currently are 5975 guests and 1 member online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
The product was good and just what I needed, however I had moderate difficulty with the down load because the sight would not recognize my pass word. I was finally given a direct link to the manual and that worked.
;
Very quick and easy website to use and fast download of manual, quality of manual is excellent and will be pleased to use this service again in the future, thanks so much!
;
It is an very good and clear scanned service manual.
very recommended.
;
Easy to order the manual. Good quality and fast delivery.
;
The Service Manual for Sansui AU-9500 was very helpfull, in complete and in good printable condition.
Thanks.
TH-K2AT/K2E/K2ET
ADJUSTMENT
J. 13.8V TX M power (Lower limit frequency, center frequency, upper limit frequency) 113.8V TX M power (Lower limit frequency) (1) Press the [LAMP] or [MONI] key on the transceiver to display �P13L� on the LCD. In this case, the � � icon appears. The current APC value is displayed at the lower digits of the frequency display, and the value stored in the EEPROM is displayed on the memory channel number display. (4) Repeat steps (4) to (7) of �113.8V TX M power (Lower limit frequency)� described on page 32. K. 13.8V TX L power (Lower limit frequency, center frequency, upper limit frequency) 113.8V TX L power (Lower limit frequency) (1) Press the [LAMP] or [MONI] key on the transceiver to display �P13L� on the LCD. In this case, the � � icon appears. The current APC value is displayed at the lower digits of the frequency display, and the value stored in the EEPROM is displayed on the memory channel number display.
(2) Press the [VFO], [MR] or [CALL] key to switch to the frequency display. (3) Turn the encoder to display the lower limit frequency on the LCD. (4) Press the [CALL] key to switch to the adjustment display. (5) Press the [PTT] key to enable the transmit mode. (6) Turn the encoder to change the current APC value and adjust the transmission power. (7) Press the [MENU] key to write the current APC value into the EEPROM. 213.8V TX M power (Center frequency) (1) Press the [LAMP] or [MONI] key on the transceiver to display �P13C� on the LCD. In this case, the � � icon appears.
(2) Press the [VFO], [MR] or [CALL] key to switch to the frequency display. (3) Turn the encoder to display the lower limit frequency on the LCD. (4) Press the [CALL] key to switch to the adjustment display. (5) Press the [PTT] key to enable transmit mode. (6) Turn the encoder to change the current APC value and adjust transmission power. (7) Press the [MENU] key to write the current APC value into the EEPROM. 213.8V TX L power (Center frequency) (1) Press the [LAMP] or [MONI] key on the transceiver to display �P13C� on the LCD. In this case, the � � icon appears.
(2) Press the [VFO], [MR] or [CALL] key to switch to the frequency display. (3) Turn the encoder to display the center frequency on the LCD. (4) Repeat steps (4) to (7) of �113.8V TX M power (Lower limit frequency)� described on page 31. 313.8V TX M power (Upper limit frequency) (1) Press the [LAMP] or [MONI] key on the transceiver to display �P13H� on the LCD. In this case, the � � icon appears.
(2) Press the [VFO], [MR] or [CALL] key to switch to the frequency display. (3) Turn the encoder to display the center frequency on the LCD. (4) Repeat steps (4) to (7) of �113.8V TX L power (Lower limit frequency)� described on page 32. 313.8V TX L power (Upper limit frequency) (1) Press the [LAMP] or [MONI] key on the transceiver to display �P13H� on the LCD. In this case, the � � icon appears.
(2) Press the [VFO], [MR] or [CALL] key to switch to the frequency display. (3) Turn the encoder to display the upper limit frequency on the LCD. 32
|
|
|
> |
|