|
Who's Online
There currently are 6018 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
Thank´s for your help, I already recived these manual from you
;
Thank you for your manual It has the basic things to and i use the Oszi for Longer Time.
THX
;
Actually, I was looking for this information for 3 years!...now thanks to you, the manual is on my hands and of great help, cause I understand now where I was doing wrong connections and wires...excellent, I'll be back to you if in need, thank you.
;
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
;
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
General features
English
Removing the Faceplate
The faceplate can be detached from the unit, helping to deter theft. Removing the faceplate: � When removing the faceplate, pull it out only when it is fully open. The detachment of the faceplate while it is moving might result in damage to the unit. � Do not apply excessive force to the faceplate bracket without attaching the faceplate. Doing so will cause the faceplate bracket to be deformed. � Do not touch the connector on the faceplate bracket after removing the faceplate. Touching the connector may cause damage to the unit. � Do not touch two metal parts on both sides of the faceplate bracket. Touching those parts may injure you.
NOTE
1 Choose the way from among the following and open the
faceplate. Turn the ignition off, press the SRC button for at least one second, or press the left part at the upper side of the faceplate (as illustrated on p.11) for as many times as you have preset in the "Manual Open Button Setting" (OPEN SW #) in the menu when the control panel has been hidden. 2 Set the faceplate's angle adjustment switch to "0" to set the faceplate angle to the vertical. For details, refer to "Faceplate Angle Adjustment" (page 13).
NOTE
If the faceplate's angle adjustment switch is not set to "0" when mounting the faceplate on the faceplate bracket, it may be difficult to mount the faceplate or the faceplate may not be securely attached and could fall off. Set the angle adjustment switch to "0" before removing the faceplate.
� Sliding the faceplate lock switch cause the unit�s power to turn off. If you want to operate the unit again, remove the faceplate from the faceplate bracket completely and then reattach it. � The faceplate is a precision piece of equipment and can be damaged by shocks or jolts. For that reason, keep the faceplate in its special storage case while detached. � Do not expose the faceplate or its storage case to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. Reattaching the Faceplate:
1 Hold the faceplate so that the control panel faces the front
toward you and set the left side of the faceplate in the faceplate bracket.
2CAUTION
3 Slide the faceplate lock switch to the left during the period
which you have set in the "Time setting for removing the faceplate" in the menu.
Do not set the right side of the faceplate in the faceplate bracket first, when reattaching the faceplate. Doing so may cause the connector on the faceplate bracket to malfunction. 2 Press the right side of the faceplate until it locks.
Faceplate lock switch
4 Holding the center part of the faceplate, pull it out.
The faceplate bracket will automatically close.
2CAUTION NOTE
If the faceplate bracket's angle was not set to the vertical when
� 12 �
|
|
|
> |
|