|
|
|
Who's Online
There currently are 5999 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I needed the manual immediately and I got it immediately. I couldn't find this manual anywhere else on the net. The site was easy to traverse, and the price was very reasonable. I'll definitely be back for any future needs.
 ;
I received a good service manual, with good resolution. Improve the instructions for the purchase because they are not well understood.
For the rest, so good.
Thanks Angel.
;
Very good documentation for the Grundig 2077 model (as well as similar 800/900/1000 series radios). The first two pages are a summary of reception specifications and output capability. The third page is the tuner dial indicator and dial cord routing diagram. the final ~5 pages are the schematics for the various models (including 2077). The scan quality of the schematics are good, adn can be easily read if zoomed in. The documents are in German, not English as stated. It would have been nice to have the tuning sequence and settings, and some trouble shooting materials... or component and wiring map.
;
Perfect like it was descriped, Perfect like it was descriped
;
Very good detail, all pages clear, exactly what I needed
KRC-165
TEST MODE / ADJUSTMENT
TEST MODE
1. How to enter the test mode
� Reset the unit while holding the Track Down key and preset 6 key. � All indication segments go ON at the beginning of the test mode. � The BASS / TREBLE and BALANCE / FADER controls can be set to the full boost / center / full cut and full right / center / full left and full front / center / full rear respectively. � Sound coordination doesn't appear for the Audio mode feed. � The inspection function of LCD When all indication segments are ON, the segments can be set to the following order respectively by pressing the Track up key / Track down keys. All indication segments � Odd segments (Common 1 part) � Even segments (Common 2 part) � Odd segments (Common 3 part) � All indication segments � When the unit is reset (backup turned on) while ACC is OFF in test mode, the MUTE terminal goes off in 2 seconds.
2. How to release the test mode
� Simply reset the unit. � (NOTE) The test mode is not canceled by ACC OFF, power OFF, momentary power down or the panel off.
3. Contents
� Set the volume level to -10dB (which is shown as "30" on the display). � Loudness OFF.
ADJUSTMENT
Set the controls and switches as follows. BALANCE : center position BASS : center position FADER : center position TREBLE : center position No. ITEM TAPE OUTPUT SETTINGS LOUDNESS : OFF
RECIEVER SETTINGS
ALIGNMENT POINTS
ALIGN FOR
CASSETTE DECK SECTION
[1]
HEAD HEIGHT
SCC-1659
-
TAPE PLAY
Head Height Screw
1) During FWD transport adjust �and �' so that line A F F of 2-LINE TAPE passes through the center of the head shield plate (core center area) 2) During RVS transport adjust � and � ' so that line B R R of 2-LINE TAPE passes through the center of the head shield plate (core center area) 3) After the alignment above, reverse the transport direction and check the FWD alignment again. If it is deviated, perform alignment again. (Tape used : SCC-1659, manufactured by A-BEX) Adjust the azimuth for each L ch/R ch or FWD/RVS becomes maximum.
[2]
HEAD AZIMUTH
TCC-153 10kHz
Connect an AC voltmeter and oscilloscope to SP outputs.
TAPE PLAY
Head Azimuth Screw
TAPE SPEED
(2-LINE TAPE)
B A (FWD)
HEIGHT (FWD)
F
'
R
'
HEIGHT (RVS)
B
HEIGHT/AZIMUTH (FWD)
F R
A
(RVS)
HEIGHT/AZIMUTH (RVS)
6
|
|
|
> |
|
