|
Who's Online
There currently are 257 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
 |
|
There are currently no product reviews.
 ;
This manual is very good. 303 pages scanned in a very high resolution. My camera has bad, leaking capacitors which all of the V5000 models are suffering from these days.
There is a huge part list with all capacitors, transistors etc. in this manual which helped me a lot. Otherwise I would not have been able to buy replacement parts.
The dissassembly guide is very enormous and detailed. Unlike on the Panasonic MS1 manual I downloaded here it actually looks like the real parts look. And the screws are labeled correctly, so you shouldn't have any left after the repair. ;)
 ;
has all the schematics you could need,and very well laid out format also has all part numbers along with an exploded view which is helpful
 ;
Very nice to have! Now it is no problem to understand how it is put together.
Helps me a lot.
 ;
good scans, all is clear. all pages in order. recommended
 ;
Très-très bon site, facile, très bon prix.
Au futur besoin, je n’hésiterais à faire appel à vous.
Merci
KDC-9026R/PSW9527 KDC-W9027/X979
TEST MODE
â Demonstration mode 1. How to enter to the Demonstration mode
1. Hold down the [Q] key and [TI (AME)] key button when the power is on and press the Reset button. 2. This will enter to the Demonstration mode. 5. Hold down the Track Up key for at least 3 seconds and the message, âRE-ENTERâ appears, so once again enter the code according to Step 4 above. 6. Press and hold the Track Up key for 3 seconds until âAPPROVEDâ is displayed. 7. Exit from the test mode. (See 2. How to exit from the test mode) Note 1 : All Clear is not applicable to the security code of this model. Note 2 : When the F/E changed, need re-inscription because the panel security is clear.
2. How to chancel the Demonstration mode
1. Hold-down the Preset [5] key button when the power is on and press the Reset button. 2. This will cancel the Demonstration mode.
â Security information 1. Forced Power ON mode (All models)
Even when the security (Cord) is approved, resetting the unit while holding the Q and Preset 4 keys makes it possible to turn the power ON for 30 minutes. After 30 minutes have elapsed, it is not possible to return to the previous condition unless the unit is reset again. (Security code is doing not clear at this mode. Put the power on fill-in.) When panel security was set up for the unit when it is can not power on. In this case, you can use new ROM for the TDF panel that the unit can be power on for test mode. Note : Donât enter the panel security set up for new ROM panel. User can not power on the unit.
3. How to inscription the panel security code
1. Enter the test mode. 2. Pressing the AM key on all lighting, check the âP-ROM WAITâ display. 3. The NEXT key is long press 2 seconds, writing the code. 4. Display is âP-ROM OKâ. 5. Exit from the test mode. Note : E2PROM connection is NG when display is âP-ROM NGâ, so detach the panel and rewrite after the display is âPROM WAITâ. This code can not clear.
4. Simple way to clear the security code (K type only)
1. During code request mode, press the Track UP key for at least 3 seconds while holding down the AUTO key. (â â â â will disappear) 2. Enter, âKCARâ with the remote controller as described below. ⢠Press the remote controller 5 key twice, and press the Track Up key. (Enters a âKâ ) ⢠Press the remote controller 2 key three times, and press the Track Up key. (Enters a âCâ ) ⢠Press the remote controller 2 key once, and press the Track Up key. (Enters an âAâ ) ⢠Press the remote controller 7 key twice, and press the Track Up key. (Enters an âRâ ) 3. Security function is canceled and unit sets to All-Off mode. 4. Code request mode appears if a mistake was made in entering the numbers.
2. Method of registration of the security code after EEPROM (F/E) replacement (Code security model)
1. Enter the test mode. (See How to enter the test mode) 2. Press the MENU key to enter the Menu mode. 3. When the message âSecurityâ is displayed, press and hold the Track Up/Down key for 1 second to enter the security registration mode. 4. Enter the code using the FM/AM/Track Up/Track Down keys. FM key : Number up AM key : Number down Track Up key : Cursor right shift Track Down key : Cursor left shift
15
|
|
 |
> |
|