|
|
|
Who's Online
There currently are 6043 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The ease of this purchase was a good start. The content of this manual was exactly all I needed to retore my Tandberg 64.
All of the mechanical and electrical information is contained in the manual and the quality of the document makes reading the data easy.
The exerience with the resource has made this my prime source for technical data.
;
Owner-manuals.com is the best Possibility to give vantage HIGH CLASS Elektronic COMPONENTS
a new Life.Thanks alot for your perfekt Service.
;
I am proud of you. In the future, I benefited from your services.
;
I found this manual to be complete in every detail. Besides the schematic it has a complete set of alignment instructions which are easy to understand. It also includes a complete parts list as well as an explanation of how the power supply and safety shutdown circuits operate. Even a schematic of the tuner is included.
 ;
The product was good and just what I needed, however I had moderate difficulty with the down load because the sight would not recognize my pass word. I was finally given a direct link to the manual and that worked.
KDC-MP6025/MP625/MP858 KDC-W6527/W6527Y
TEST MODE
� How to enter the Test Mode
Reset while pressing both [1] key and [3] key.
� Special Display in the TUNER Mode
In the TUNER mode, there are abnormalities in the front end, etc. when the following displays are made. � �TNE2P_NG�: E2PROM is still in the initial value (unspecified value) due to F/E being shipped without going through the adjustment process or other reasons. � �TNCON_NG�: There is no communication with the F/E.
� How to release the Test Mode
The Test Mode can be released by resetting. The Test Mode is also released when there are: a momentary power down, Acc OFF, power OFF, and panel detachment.
� Initial condition of the Test Mode
The following are initial conditions of the Test Mode: � The source in standby mode. � The displays all lit up. � Volume is -10dB (display will be 30). � LOUD is OFF. � CRSC is OFF regardless of whether the switching function is effective or not. � SYSTEM Q is in NATURAL. � SRS WOW are all OFF. � BEEP will be a short one at all times. � AUX is ON. � SYSTEM Q on the MENU is OFF. � GUIDE (NAVI) on the MENU is ATT. � DISPLAY TYPE is TYPE A.
� Forced Switching of K3I
In TUNER mode, every time the [6] key is pressed, the following takes place: AUTO � Forced WIDE � Forced MIDDLE � Forced NARROW � AUTO. The initial condition is AUTO and there will be the following displays: � AUTO � Forced WIDE : FMA : FMW
� Forced MIDDLE : FMM � Forced NARROW : FMN Note : In synchronization with the above changes, numbers 1 through 3 are displayed but these are to be ignored.
� CD Receiver Test Mode Specifications
� With key, there will be jumps to the following tracks: No. 9 � No. 15 � No. 10 � No. 11 � No. 12 � No. 13 �
� RDS Automatic Measurement
Conventionally, the visual inspection on the PS display has been conducted on the production line. From now on, a measure will be added to replace this. PS data is received and the PS contents is confirmed to be �RDS_TEST�, the P-CON terminal is forced to go OFF. (�_� means blank.) This is a measure specific for the Test Mode. P-CON is recovered by switching the source or by power OFF�ON.
No. 22 � No. 14 � No. 9 (Back to the beginning) However, when playing MP3/WMA disks with 8 files or less, tracks will be played in sequence as usually, beginning with Track1. � When key is pressed, the previous track from the cur-
rent one will be played. � While playing from CD sources, when [1] key is pressed intermittently, there will be a jump to No. 28. � With models that have MP3 or MP3/WMA mechanism, the model name and version will be displayed in the lower column. � When [6] key is pressed, there will be a jump to No. 15. When this takes place, the value is set to 29 (eXcelon model) or 26 (other models).
11
|
|
|
> |
|
