There are currently no product reviews.
First, thank you very much for the fast delivery.
I'm really satisfied with your manual. I could find everything, I needed.
I appreciate your service.
Regards from Germany PB
Everything you need: schematic, circuit explanation, operating/testing instructions. Awesome.
Correct and accurate service manual for that Siemens (Nordmende) TV. Price is worthwhile as the Manual is fully usable.
Just what I needed to repair my CT-F600, clear pdf, easy to tread and navigate
Yes, cost is low. And quality of some diagrams is low too.
KDC-3022,322,5023/R,5024/V/Y/YV,507,5094RY TEST MODE
1. How to enter the test mode
â¢ While holding the preset 1 key and 3 keys, reset the unit. â¢ When the number of total tracks of an MP3 disc is nine or less, unit playback from a track 1. â¢ When the media to CD-DA, unit playback from track No.28 by key operation of preset 1 key.
2. How to exit from the test mode
â¢ Reset the unit, ACC OFF, power OFF, and come off the front panel assy for the unit.
7. Audio-related specifications
â¢ A short press of the Q key initiates the audio adjustment mode. â¢ Pressing the â½ key on the remote initiates the audio adjustment mode. â¢ Continuous holding of a remote control key is inhibited. â¢ Bass, Middle and Treble are adjusted in 3 steps of -8 / 0 / +8 with the Track Up/down keys (default is 0). â¢ Balance is adjusted in 3 steps of Left L15 / 0 / R15 Max with the Track Up/down keys (default is 0). â¢ Fader is adjusted in 3 steps of Rear15 / 0 / F15 Max with the Track Up/down keys (default is 0). â¢ HPF is adjusted in 2 steps of Through/170Hz (or 200Hz) with the Track Up/down keys (default is through). â¢ LPF is adjusted in 2 steps of Through/120Hz with the Track Up/down keys (default is through). â¢ Bass f, Bass Q, Bass EXT, Middle f, Middle Q and Treble f are not dealt with by the audio adjustment.
3. Initial status in the test mode
â¢ Sources â¢ Display â¢ Volume â¢ Loudness â¢ CRSC â¢ SYSTEM Q â¢ Aux â¢ Display color â¢ Beep sound : All OFF. : All segments were lit. : -10 dB (displayed as 30) : OFF : OFF regardless of the presence of switching function. : Flat. : ON : white (variable color display model only) : ON
4. Special display in Tuner mode
When any of the following messages is displayed in Tuner mode, the Front-end (F/E) may be bad condition. â¢ "TNE2P NG": The EEPROM is set to the default (unstable values) because the F/E was shipped without passing through the adjustment process, etc. â¢ "TNCON NG": Communication with the F/E to microprocessor is not possible.
8. Menu-related specifications
â¢ A short press of the PLAY/PAUSE key initiates the Menu mode. â¢ Pressing the DNPP key on the remote initiates the Menu mode. â¢ Continuous holding of a remote control key is inhibited. â¢ Contrast is adjusted press of the Track up/down key in 3 steps of 0 / 5 / 10 (default is 5).
5. Forced switching of K3I
Each press of the Preset 6 key in Tuner mode should switch K3I from AUTO Â¡ Forced Wide Â¡ Forced Middle Â¡ Forced Narrow Â¡ AUTO. The initial status is AUTO and the display shows these modes as follows. â¢ AUTO : FMA â¢ Forced Wide : FMW â¢ Forced Middle : FMM â¢ Forced Narrow : FMN
9. Backup current measurement
When the unit is reset while ACC is OFF (i.e. by turning Backup ON), the MUTE terminal goes OFF in 2 seconds in place of 15 second. (The CD mechanism is not activated at this time.)
6. Test mode specifications of the CD receiver
â¢ Forced ejection is inhibited in the reset start operation. When the unit is reset while a CD is loaded in it, the CD is not recognized by resetting. â¢ Each press of the Track Up key jumps to the following track numbers: No. 9 Â¡ No. 15 Â¡ No. 10 Â¡ No. 11 Â¡ No. 12 Â¡ No. 13 Â¡ No. 22 Â¡ No. 14 Â¡ No. 9 (The cycle restarts from here.) â¢ Each press of the Track Down key jumps to the previous track number to the track being played.