There are currently no product reviews.
- Very good scan quality, PERFECT!
- Sehr gute scan Qualitaet, empfehlenswert!
Good site, works ok and you get what you order, no problems experienced, got my manual within a day. A++++
Original well scanned manual. Got the job done. Microwave problem found & corrected. For $5 and a new magnitron from ebay, it was a cheap and good the first shot fix. Electrical schematics allowed me to mage sure every thing else was ok before cutting and order for parts. Hard to live without.
I was very skeptical of this website, I have never downloaded manuals before. I put it on the AMEX and payed through Paypal to ensure protection. I got the manual exactly as described and now I can replace the filter capacitor for this amp. Great Price, others selling for 12.99 or more and this is the same manual. I will search out this website for other manuals. Thank you
Manual was reasonably easy to follow. I am not an engineer or know much about electronics but with the manuals help I was able to figure out the problem, identify the part required for the repair. Replacement part cost around $30. Whilst replacing the part I was telling myself, "this aint gonna work cos it seems far too easy". Took about 15 minutes to do and my plasma TV works a treat. Would never have been able to do this without the service manual.
1. IC10 (TDA7513) -The Tuner adjustment method
â¢ When IC10 and its circumference are fixed, according to the following order, it readjusts if needed. â¢ The adjustment item changes with parts to exchange. Please refer to "Parts vs Adjustment item table". 1-1. VCO Coil Adjustment -- Adjustment of Tunning Voltage Voltage Check Point : Vt-Check Land (PWB Side_B, around D506) Adjustment Coil : L507 (VCO Coil) The adjustment method : VCO coil is turned and adjusted according to the following tables.
TYPE E/M K J W(Wide Band) Mode AM AM FM FM freq. 1611kHz 1700kHz 90.0MHz 108.0MHz Voltage 5.5 Â± 0.1(V) 5.8 Â± 0.1(V) 5.6 Â± 0.1(V) 7.2 Â± 0.1(V) Fig (C) (C) (C) (C)
1-3. Adjustment of FM_ANT&RF Coil Voltage Check Point : S_METER-Check Land (PWB Side_B, around W572) Adjustment Coil : ANT_Coil = L505 RF_Coil = L506 Setting of Signal Generator : Refer to the following tables.
TYPE E/M K J W(Wide Band) MODE FM FM FM FM freq. 87.5MHz 87.9MHz 76.0MHz 65.0MHz Mod. OFF OFF OFF OFF ANT Input 5 or 11dBuEMF 5 or 11dBuEMF 5 or 11dBuEMF 5 or 11dBuEMF Fig (A),(C) (A),(C) (A),(C) (A),(C)
xThe appearance and the coil with which S-METER DC voltage serves as the maximum are turned and adjusted in the above-mentioned SG input. âBy the above-mentioned adjustment method, same adjustment is performed to both sides (ANT&RF Coil). 1-4. Adjustment of STEREO (adjustment of 456k-VCO) Adjust in TEST_MODE â¢ How to enter the test mode While pressing on [ FM ] and [ PRESET 6 ] keys, reset the unit. â¢ Adjustment method Complete on condition that show "ALL OFF" when pressing on [ PRESET 1 ] and [ PRESET 6 ] keys. (Writing adjustment valve to the EEPROM.) Effect of adjustment is in cofirmation of adjustment status at [ PRESET 4 ] key. â¢ Display of [ PRESET 4 ] Adjustment "OK" : 14seg model "E2P OK" 7seg model "EPO" Adjustment "NG" : 14seg model "E2P ERR" 7seg model "EPE" â¢ Releasing the test mode Reset mode only. ACC off, Power off, Power down and Remove the panel mode is not releasing.
M : AM Adjustment For Your Information : The frequency of SET is only set up by Pre-Set-Key in case this adjustment 1-2. Adjustment of 1st & 2nd-MIX Coil Voltage Check Point : S_METER-Check Land (PWB Side_B, around W572) Adjustment Coil : 1stIFT = L508 / 2ndIFT = L509 Setting of Signal Generator : Refer to the following tables
TYPE K E,M,J,W MODE AM AM freq. 1000kHz 999kHz Mod. OFF OFF ANT Input 35dBuEMF 35dBuEMF Fig (B),(C) (B),(C)
xThe appearance and the coil with which S-METER DC voltage serves as the maximum are turned and adjusted in the above-mentioned SG input. âBy the above-mentioned adjustment method, same adjustment is performed to both sides (1st&2nd MIX Coil).
L505 L506 L507 L508
(C) DC Voltmeter Vt Check Land IC10
S-METER Check Land (OVER VIEW) (UNDER VIEW)