|
Who's Online
There currently are 5998 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
For five bucks you can barely buy a hamburger. Or for the same five bucks you can buy a service manual. Much more useful. (and better for your health, depending on where you buy your hamburgers).
Yes, there are free manual sites out there, but if they don't have what you want, you have to pay.
And five bucks isn't much. Not for full specs, schematics and adjustment and parts replacement procedures.
My only criticism is that grayscale illustrations aren't well rendered, but I've seen worse.
Schematics and text are clear.
I'll be happy to purchase from here again.
Mike
[email protected]
;
Impressively thorough. Even the simple operators manual helped me "fix" one of the 2 CD players in the unit. This unit reads CD's from the top so they should be installed in the magazines "upside down" from typical CD players. The CD player service manual helped me unjam a stuck carriage because somebody transported the box laying down loaded with CD's. A little lens cleaning & the player now works well! Thanks for you help at a great price! Joe
;
I was skeptical at first but later found the manual to be good quality for the price. It took a couple hours to receive the email with the download link, well worth the wait. Thanks.
;
very helpful, I could not have cleaned motherboard and replaced the main fan without it
;
Good manual, schematics nice and clear with good quality scanning. Woul dhave been nice to have immediate access after purchasing though.
KDC-2019/V/217/S/219/29MR /2020/3020/4020
MICROCOMPUTER�S TERMINAL DESCRIPTION / ADJUSTMENT
Pin No. 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 Pin Name LOE/LIM SW MOSW LO/EJ M-STOP M-RST M-MUTE RESET REMO R-CLK CH-REQC LOS SW KEY-REQ 12EJE SW Vss0 VDD1 X2 X1 IC XT2 XT1 VDD0 AVREF0 S-METER PHONE NOISE NC AVCONT I/O I O I/O O O I I I I I I I I I I I I I O O Purpose CD mechanism Down & Limit detection CD mechanism motor switching Lo/Ej switching Mechanism COM stop output Mechanism COM reset output Mechanism COM mute input System reset input Remote control input RDS CLOCK 5-wire CH request (CH) Loading SW detection Key input detection 12 cm disc detection GND potential (for ports) Positive power supply (for other parts than ports and analog circuitry) Main system clock oscillation Main system clock oscillation Flash uCOM write Not used Not used (Connected to 5V power supply) Positive power supply (for ports) 5V power supply (A/D converter reference voltage) S-meter input Hi-Z L Hi-Z L H Hi-Z Hi-Z Hi-Z Hi-Z, L when RDS is not available. Hi-Z, L when CH is not available. Hi-Z Hi-Z Hi-Z Hi-Z Processing in STBY Mode
Navigation muting 2.5V or more, Telephone muting 1V or less. Hi-Z, L when TEL is not available. FM noise detection Not used A/D reference voltage control Hi-Z, L when RDS is not available. L L
ADJUSTMENT
No. ITEM INPUT SETTINGS TUNER (RECEIVER) SETTINGS ALIGNMENT POINTS ALIGN FOR
FM SECTION While holding preset �1� key, press and 98.1MHz 1 SD 0 dev 35dBµ (ANT input) AM SECTION While holding preset �1� key, press and 990kHz (1) SD 0% mod 35dBµ (ANT input) TEST MODE : ON TEST MODE : OFF TEST MODE : ON AM 990kHz Preset �1� key, and preset �6� key hold preset �6� key for a few seconds. �1111� is good. �0000� is not good. TEST MODE : ON FM 98.1MHz Preset �1� key, and preset �6� key hold preset �6� key for a few seconds. �1111� is good. �0000� is not good.
While holding the FM key and preset �6� key, reset the unit. Reset the unit.
4
|
|
|
> |
|