There are currently no product reviews.
Some of the pictures in this manual are a bit irritating. I had to dissassemble the unit and some of the screws have different threads, which is not mentioned in this manual. Also some of the drawings of the boards look different than the actual boards.
After all, the manual was very useful. I was able to recalibrate the capstan drive and it is working fine again.
This manual is very good. 303 pages scanned in a very high resolution. My camera has bad, leaking capacitors which all of the V5000 models are suffering from these days.
There is a huge part list with all capacitors, transistors etc. in this manual which helped me a lot. Otherwise I would not have been able to buy replacement parts.
The dissassembly guide is very enormous and detailed. Unlike on the Panasonic MS1 manual I downloaded here it actually looks like the real parts look. And the screws are labeled correctly, so you shouldn't have any left after the repair. ;)
has all the schematics you could need,and very well laid out format also has all part numbers along with an exploded view which is helpful
Very nice to have! Now it is no problem to understand how it is put together.
Helps me a lot.
good scans, all is clear. all pages in order. recommended
ACCESSORIES / CAUTIONS
Audio video cord (Red, White, Yellow) ...(1) (E30-2990-08) Remote control unit ...(1) (A70-1570-08) Batteries(R6/AA) ...(2) Coaxial cable ...(1) (E30-7235-08)
Operation to reset
The microprocessor may fall into malfunction (impossibility to operate erroneous display, etc.) when the power cord is unplugged while power is ON or due to an external factor. In this case, switch off the power, wait for several seconds, and then switch the power on again. Return to the factory defaults by resetting the microprocessor is done as shown as follows.
During stop mode, press the MENU key on the remote to enter "Control Panel" menu. Select the "System" icon, then press the Cursor right ( ) key. Select "Restore Setup Info". Press the numeric keys as shown below. Press , , , , then press the ENTER key. When resetting is done according to this method, all settings, including the settings for password and parental level, will be reset to the factory defaults.
Note related to transportation and movement
Before transporting or moving this unit, carry out the following operations. 1. Set the POWER ON/OFF switch to the ON without loading a disc. 2. Wait a few seconds and verify that the display shown appears.
Caution on condensation
Condensation (of dew) may occur inside the unit when there is a great difference in temperature between this unit and the outside. This unit may not function properly if condensation occurs. In this case, leave the unit for a few hours and restart the operation after the condensation has dried up. Be specially cautious against condensation in the following circumstances: When this unit is carried from one place to another across a large
3. Set the POWER ON/OFF switch to OFF.
difference in temperature, when the humidity in the room where this unit is installed increases, etc.
The marking of products using lasers
(For countries other than U.S.A. and U.S.-Military)
CLASS 1 LASER PRODUCT
VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. DO NOT STARE INTO THE BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS.
DO NOT PRESS ON THIS SURFACE
The marking this product has been classified as Class 1. It means that there is no danger of hazardous radiation outside the product. Location: Back panel Inside this laser product, a laser diode classified as Class 2 laser radiation is contained as alerted by the internal caution label shown above. Do not stare into beam or view directly with optical instruments. Location: DVD laser pick-up unit cover inside this product
Manufactured under license from Dolby Laboratories. "Dolby" and the double-D symbol are trademarks of Dolby Laboratories. "DTS" and "DTS Digital Out" are trademarks of Digital Theater Systems, Inc.
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, the following are reproductions of labels on, or inside the product relating to laser product safety. KENWOOD CORPORATION 2967-3, ISHIKAWA-CHO, HACHIOJI-SHI, TOKYO, JAPAN KENWOOD CORP. CERTIFIES THIS EQUIPMENT CONFORMS TO DHHS REGULATIONS NO. 21 CFR 1040.10, CHAPTER 1, SUBCHAPTER J. Location: Back Panel CAUTIONLASER RADIATION WHEN OPEN. DO NOT STARE INTO BEAM.
Location: Laser Pick-up Unit Cover inside this product